COVID-19 UPDATE - We are still shipping daily during the COVID19 pandemic and South Australia lockdown. Please note some slight delivery delays may occur due to border crossing delays.
Magigoo PA Nylon Adhesive Magigoo PA Nylon Adhesive Magigoo PA Nylon Adhesive
Magigoo PA 50ml 3D Printing Adhesive

3D printing adhesive for Nylon (PA).

AUD ($34.95 Incl Gst) $31.77 Ex Gst
Sold out.
Add to wish list

Magigoo PA 3D Printing Adhesive

MAGIGOO PA is designed for professional use, to work exclusively with Polyamide filaments. The part should be relatively easy to remove once it cools and the glue residue should also be easily cleaned off.

PA (polyamide) describes a group of polymers with an amide repeat unit. Generally in the FDM industry there are 3 main types of PA which include PA12, PA6,6 and PA6, sometimes these materials can be either grafted with other polymers or else reinforced with glass or carbon fibres. Generally nylons exhibit high strength, toughness, elasticity, wear resistance, chemical resistance and thermal resistance and are widely sought in various industrial applications.

Nylon filaments prove to be challenging materials for FDM printing due to their lower adhesion to conventional 3D-printing build surfaces and their higher tendency to warp. Furthermore there are several classes of PA filaments each behaving differently. MAGIGOO-PA is a specialized solution for FDM printing of PA filaments which was developed to work with a wide number of PA types.

Important note

Using this product with other than PA type filaments might cause over adhesion and damage your build surface.

The applicator has an active spring valve, which activates when applicator is pressed against the build plate. Please do not press the bottle as "ketchup bottle" , otherwise the applicator may pop off. Bottle may be slightly squeezed, only when the nib is pressed against the bed and it may be necessary only if bigger flow is required. Bottle must not be squeezed when cap is off any other time as it may result in glue popping out of the bottle.

Magigoo 3D Printing Adhesive

How to use
  • Shake the bottle.
  • Apply to the desired area by pressing the nib on the bed (activating the inner valve) and spreading as needed.
  • Print according to the filament/printer manufacturers recommendations.
  • Allow to cool and Remove. The print should pop right off.*
  • Clean - Use a damp cloth to wipe off. 

In cases of excess adhesion, it is recommended to wet print bed with a small amount of water slowly work it below the part, this should make part removal easier. If your prints are not self releasing after the bed cools, increasing the z offset (nozzle gap) may be required.


Storage

MAGIGOO PA is best stored upright, with the cap closed and away from direct sunlight.


FAQ

Q: How do I apply Magigoo?
A: It is best to apply Magigoo when the printing bed is cool. Before applying, shake the Magigoo pen like you mean it, press down the nib on the printing bed for Magigoo to flow. Spread more or less evenly on the printing area. It is enough to cover your active print area with an even thin layer. DO NOT SQUEEZE the bottle to avoid applicator popping off. Applicator has a valve which is activated once you push on it.

Q: Do I need to apply Magigoo everytime?
A: For good and reliable adhesion we recommend to apply Magigoo every time.

Q: How do I clean my bed after using Magigoo?
A: After your prints have finished and popped off, clean the printing bed by wiping with a damp cloth. Yes, just water is enough. 

Q: How long will Magigoo last for?
A: One Magigoo 50ml pen is good for on average 100 prints. There is no firm best before date as it will vary depending on use and storing conditions - Once opened, we recommend to use it in a couple of months. 

Q: Will Magigoo work with my existing printing surface?
A: Magigoo was originally formulated with borosilicate glass surfaces in mind however we have also had good success applying Magigoo to surfaces like Buildtak, in these cases Magigoo can work as a release agent for materials which can over-adhere.

3D Printing Solutions was established in 2013 by CEO Michael Tyson to distribute high quality 3D printers and supplies to enthusiasts, businesses, government and educational institutions across Australia and New Zealand.

Australian owned and operated, here at 3D Printing Solutions we are dedicated to ensuring your success by providing high quality solutions and sharing our years of hands on experience and support. One of our key philosophies is to thoroughly test the printer brands and filaments we sell to ensure they meet our key quality standards. Our collaborative and in-depth experience with these brands ensures we can provide detailed comparisons and advice to customers.

Key Benefits

  • Australian owned online and retail store operated since 2013.
  • Quality assured products.
  • Free shipping on orders over $150 across Australia* (* Excludes select products where noted and delivery to some remote regions.)
  • Official Magigoo reseller.
  • We have hands on experience using Magigoo products. Phone, email and local support handled by our trained and knowledgeable staff.
  • Growing list of online resources for beginners and advanced users.
  • Support and warranty handled locally in Australia.

Need Help?

Dont know where to start? Or which filament will suit your application?

We have a broad range of support options including Telephone Support

  Contact Us