Now available in an XL bottle! 120 ml lasting you more than 200 prints!
Magigoo is an easy to use 3D printing adhesive designed to address 'the first layer not sticking problem'. Magigoo ensures a strong adhesion to the hot plate. But the magic starts when printing is ready: just wait for the plate to cool down and then remove your prints with just a finger flick! In addition, Magigoo helps to prevent warping. Isn't it magic? Regardless of you being a hobbyist or professional - it is extremely rewarding to have a 30 hour print complete without any warping and having it release easily once cooled.
- XL Bottle lasting over 200 applications
- ABS, PLA, PETG, HIPS, ASA, TPU
- Easy application
- Easy release
- Easy clean
- No smell
- No additional tools needed
- Easy to transport
- Nicer print finish
Easy application: Applying Magigoo is as easy as child's play. Shake, press, apply. Spread on an active printing area only. No need to cover the whole surface
Easy-release: Magigoo adhesive properties are designed to release the 3D print once the build plate has cooled.
Easy-clean: Magigoo is easily cleaned with water.
Long-lasting: Magigoo last for 100+ average prints for a 50ml bottle.
Odorless and safe: Magigoo is safe to use - be it in a closed room or educational workshop with kids.
The applicator has an active spring valve, which activates when applicator is pressed against the build plate. Please do not press the bottle as "ketchup bottle" , otherwise the applicator may pop off. Bottle may be slightly squeezed, only when the nib is pressed against the bed and it may be necessary only if bigger flow is required. Bottle must not be squeezed when cap is off any other time as it may result in glue popping out of the bottle.
How to use
- Shake the bottle.
- Apply to the desired area by pressing the nib on the bed (activating the inner valve) and spreading as needed.
- Print according to the filament/printer manufacturers recommendations.
- Allow to cool and Remove. The print should pop right off.*
- Clean - Use a damp cloth to wipe off.
In cases of excess adhesion, it is recommended to wet print bed with a small amount of water slowly work it below the part, this should make part removal easier. If your prints are not self releasing after the bed cools, increasing the z offset (nozzle gap) may be required.
Suggested Bed Temperature*
PLA: 40 - 60 °C
ABS: 90 - 110 °C
PETG: 60 - 85 °C
HIPS: 90 - 110 °C
* may vary for different printers and filament brands.
MAGIGOO Original is best stored upright, with the cap closed and away from direct sunlight.
Q: How do I apply Magigoo?
A: It is best to apply Magigoo when the printing bed is cool. Before applying, shake the Magigoo pen like you mean it, press down the nib on the printing bed for Magigoo to flow. Spread more or less evenly on the printing area. It is enough to cover your active print area with an even thin layer. DO NOT SQUEEZE the bottle to avoid applicator popping off. Applicator has a valve which is activated once you push on it.
Q: Do I need to apply Magigoo everytime?
A: For good and reliable adhesion we recommend to apply Magigoo every time.
Q: How do I clean my bed after using Magigoo?
A: After your prints have finished and popped off, clean the printing bed by wiping with a damp cloth. Yes, just water is enough.
Q: How long will Magigoo last for?
A: One Magigoo 50ml pen is good for on average 100 prints. There is no firm best before date as it will vary depending on use and storing conditions - Once opened, we recommend to use it in a couple of months.
Q: Will Magigoo work with my existing printing surface?
A: Magigoo was originally formulated with borosilicate glass surfaces in mind however we have also had good success applying Magigoo to surfaces like Buildtak, in these cases Magigoo can work as a release agent for materials which can over-adhere like PET with PEI.